Garage Insulation R-Value Calculator
Posted by MN Garage Notes Editorial Team Published
Total R-value is the sum of every layer's R: thickness times R per inch for each insulation layer, plus any labelled R you enter, plus the air films on each face. U is 1 divided by R, and heat loss per square foot per hour is the temperature difference divided by R. R-per-inch figures are ranges from a U.S. Department of Energy guide, marked "approximate and for general comparison only", so the calculator lets you choose the low, middle or high end. Framing lowers the real value of a wall or ceiling, and this tool does not model it.
Garage insulation R-value calculator
Pick the surface and stack up to three layers. Results update as you type and are saved in the page address. Nothing leaves your browser. Thickness is in inches and temperatures in degrees Fahrenheit.
How the garage insulation R-value calculator works
Heat has to pass through every layer in turn, so their resistances add. For each layer the calculator multiplies thickness by the R-per-inch value you choose (low, middle or high end of the published range). It adds an R-value you enter yourself, then the two air films, to get total R. The U-factor is its reciprocal, and the heat lost per square foot is the temperature difference divided by total R.
R-total = Σ (thickness × R per inch) + R-labelled + R-films U = 1 ÷ R-total heat loss per ft² (BTU/h) = ΔT ÷ R-total = U × ΔT
- R per inch
- from the published range for the material (table below)
- R-films
- 0.17 outside + 0.68 inside = 0.85 when included
- ΔT
- indoor minus outdoor temperature, °F
Worked example
Given: one layer: 2 in of XPS (R-5.0 per inch); air films included; indoor 50 °F, outdoor -8 °F (ΔT = 58 °F).
- Insulation:
2 in × 5.0 = R-10 - Add the air films:
10 + 0.85 = R-10.85 - U-factor:
1 ÷ 10.85 = 0.09 - Heat loss per square foot:
58 ÷ 10.85 = 5.35 BTU/h per ft²
Answer: R-10.85 at the center of the insulation, losing about 5.35 BTU/h per square foot at that difference. Framing and gaps make a real assembly worse.
R per inch by material
| Material | Low | High | Source |
|---|---|---|---|
| Fiberglass batt, standard density | 2.9 | 3.8 | Source 1, Table 3.2 |
| Fiberglass batt, high density | 3.7 | 4.3 | Source 1, Table 3.2 |
| Mineral wool batt | 3.7 | 3.7 | Source 1, Table 3.2 |
| EPS rigid foam board | 3 | 4 | Source 1, Table 3.2 |
| XPS rigid foam board | 5 | 5 | Source 1, Table 3.2 |
| Polyisocyanurate rigid foam board | 5.6 | 8 | Source 1, Table 3.2 |
| Spray foam, open-cell (low density) | 3.5 | 3.8 | Source 1, Table 3.2 |
| Spray foam, closed-cell (medium density) | 7 | 9 | Source 1, Table 3.2 |
Each value is stored with its source link and date in the site's data files. Reflective foil has no R per inch: use a manufacturer's tested assembly R in the labelled box.
Reference levels shown in the result
| Surface | Level | What it is |
|---|---|---|
| Ceiling, zones 6 and 7 | R-49 | 2012 IECC minimum for new heated homes, as printed in the DOE guide (source 1) |
| Attic, zones 6 and 7 | R-49 (3 to 4 in present) or R-60 (none) | ENERGY STAR recommendation (source 3) |
| Wall, zones 6 and 7 | R-13 + R-10 or R-20 + R-5 (nominal totals 23 and 25) | 2012 IECC wood-frame wall minimum for new heated homes (source 1); cavity plus continuous insulation, ignoring framing |
| Garage door | None shown | No DOE or ENERGY STAR page opened gives one |
These are reference points for comparison. They are not requirements for an unheated or lightly heated garage, and not a code opinion; your local code and adoption decide.
Assumptions and limits
- The result is the R-value at the center of the insulation. Thermal bridging through studs, joists, door rails and fasteners lowers it, and the tool does not subtract anything because no framing factor was found in a source we opened. Real walls and doors are worse.
- Insulation compressed into a thinner space gives less than its rated R, and gaps and air leaks bypass it.
- The same air-film values are used for all surfaces, although the DOE guide gives them for walls.
- R-per-inch values change with density, age and temperature, and rigid foam can lose some R as gas escapes. Use the manufacturer's data sheet for the product you buy.
- No prices, payback or code verdicts are given. Fire separation between an attached garage and the house, and foam fire or ignition barriers, are local code topics: ask your building department.
Next: see what the better R-value does to your heating load with the heat-loss heater estimator.
Frequently asked questions
What R-value should a garage door have?
No DOE or ENERGY STAR page we opened gives a recommended R-value for a garage door, so this tool shows no target for doors. Use the R-value on your door's label or data sheet, and note that a labelled panel R is not the whole-door R: joints, frames and gaps let heat through.
Do air films really count?
They add a little: the guide we cite uses 0.17 on the outside and 0.68 on the inside, 0.85 together, for a vertical surface. They matter most for thin assemblies such as a single-layer door. The calculator applies the same values to every surface and lets you switch them off.
Why is my real wall worse than the calculated R?
The calculation is for the center of an insulated cavity. Studs, plates and joists conduct heat around the insulation (thermal bridging), compressed insulation loses R, and gaps let air move. The tool does not take a percentage off for framing because we found no sourced framing factor. Treat the result as an upper bound.
Is reflective foil insulation counted?
No. DOE describes reflective insulation as working by reducing radiant heat transfer, and its effect depends on the adjacent air space and the direction of heat flow, so it has no R-per-inch value. If a manufacturer publishes a tested R for your complete assembly, enter it in the labelled R box.
Does this tell me if my garage meets code?
No. It does not check code compliance. The IECC and your local adoption set insulation rules for homes, and fire separation between an attached garage and the house is a separate code question. Ask your building department.
Which climate zone is Minnesota?
The reference table covers zones 6 and 7, the default for this site. Look up your county on the DOE or IECC climate zone map to be sure; zone boundaries follow county lines.
Sources and further reading
- DOE Building America Best Practices Series, "Energy Renovations: Insulation. A Guide for Contractors to Share With Homeowners" (May 2012): Table 3.2 insulation materials (R per inch), Table 2.1 IECC minimum R-values (www1.eere.energy.gov) Opened 2026-11-17.
- U.S. DOE, Insulation Fact Sheet (DOE/CE-0180, 2008): R-value, thermal bridging, reflective insulation (energystar.gov) Opened 2026-11-17.
- ENERGY STAR, Insulation R-values (Seal and Insulate): attic levels, zones 6 and 7 (energystar.gov) Opened 2026-11-17. Page undated.
- Building Science Corporation / DOE Building America, Guide to Insulating Sheathing (rev. Jan 2007): air films 0.17 and 0.68 (www1.eere.energy.gov) Opened 2026-11-17.