Go to main content

Epoxy Garage Floor Coverage Calculator

Posted by Published

The coating you need is the floor area divided by the coverage per gallon, times the number of coats, plus waste. The coverage figure is the one number this calculator cannot know: it comes from the data sheet of the exact product you plan to buy, at the film thickness that sheet specifies, and it changes with how porous the concrete is. Enter it yourself. The default is one example taken from one opened data sheet and is not a typical or recommended value. Read the SDS, ventilate and wear the protection the label calls for before opening any coating.

Epoxy garage floor coverage calculator

Enter your floor and the numbers from your product's data sheet. Results update as you type and are saved in the page address. Nothing leaves your browser. Sizes are in feet and coverage in square feet per gallon.

Floor and product details

Cabinets, a workbench footprint or a step you will not coat.

Replace this. 300 is only the low end of one example (Rust-Oleum ROC-109, smooth concrete), not a typical or recommended value. Use your product's practical coverage for your surface.

As the data sheet specifies.

Planning assumption for spills and leftovers. Not a sourced value. Some sheets already assume loss.

Total mixed volume per kit or container, from the label.

From the flake maker's data sheet. Leave blank to skip.

Coating needed

How the epoxy coverage calculator works

The calculator takes the area you will coat, divides it by the coverage the manufacturer states for one gallon, multiplies by the number of coats and adds your waste allowance. It then divides by the size of the kit or container and rounds up, since you cannot buy part of a kit. Flake weight is the area times the flake rate you enter.

Gallons, kits and flake
area = length × width − area not coated
gallons = area ÷ coverage × coats × (1 + waste)
kits = ceil( gallons ÷ kit size )
flake (lb) = area × flake rate
coverage
square feet per gallon from the product data sheet, for your surface and the film thickness it specifies
waste
your planning allowance as a fraction (10% = 0.10)
kit size
gallons in one kit or container as labelled

Worked example

Given: floor 22 × 20 ft, minus 40 sq ft not coated; coverage 300 sq ft per gallon (the example value); 2 coats, 10 percent waste, 1.5 gallon kits, flake rate 0.1 lb per sq ft.

  1. Area: 22 × 20 − 40 = 400 sq ft
  2. Gallons: 400 ÷ 300 × 2 × 1.10 = 2.93 gal
  3. Kits: 2.93 ÷ 1.5 = 1.96, rounded up to 2 kits (3 gal, 0.07 gal left over)
  4. Flake: 400 × 0.1 = 40 lb

Answer: 2 kits of 1.5 gallons for these example numbers. With a different data-sheet coverage the answer changes a lot: read the table below.

Why you must enter your own coverage

Coverage printed on three data sheet entries, to show the spread (examples, not recommendations)
Data sheet entryCoverageSource
Rust-Oleum ROC-109 1-part epoxy floor paint, smooth concrete (low end of 300-400) 300 sq ft/galSource 1
Same product, porous or profiled concrete (low end of 180-220) 180 sq ft/galSource 1
Armor Garage Heavy Tonnage Epoxy, 100% solids, at 30 mils 125 sq ft/galSource 2

One product's number does not transfer to another product, film thickness or surface. Each value is stored with its source link and date in the site's data files.

Assumptions and limits

  • Coverage per gallon is an input. The tool does not look up, estimate or recommend any product, and it states no coverage, cure time or recoat time as fact.
  • The waste default (10 percent) is a planning assumption, not a sourced figure.
  • It does not say the slab is ready to coat. Moisture testing, cleaning, grinding or etching and crack repair come from the manufacturer's instructions.
  • Quantities for primers, base coats, topcoats and flakes are separate products with separate data sheets: run the calculator once per product.
  • No prices are shown. Ventilate, wear the PPE the label calls for, read the SDS, and see epoxy garage floor safety.

Frequently asked questions

How much epoxy do I need for a 2-car garage?

Enter your floor size and your product's coverage. Area divided by coverage gives gallons for one coat; multiply by the number of coats the data sheet specifies and add waste. A 20 x 22 ft floor is 440 sq ft; at a coverage of 300 sq ft per gallon that is about 1.5 gallons per coat before waste. Your product's number can be very different.

Where do I find the coverage per gallon?

On the product's technical data sheet (TDS) or label: look for "practical coverage" or "coverage per gallon" at a stated film thickness, and the notes about porous or smooth concrete. Use the figure for your surface and the coats the sheet specifies. Theoretical coverage at 1 mil is a different number and overstates what you will get.

What waste percentage should I use?

It is your planning margin for spills, roller absorption, uneven slab and leftovers in the mixing pot. The default of 10 percent is an editorial planning assumption, not a sourced value. Some data sheets already assume material loss in their "practical" coverage, so check before adding more.

Does it tell me whether my concrete is ready for epoxy?

No. Whether a slab is dry enough, clean enough and profiled correctly is decided by the manufacturer's moisture test and preparation instructions. Follow them before buying coating.

How much decorative flake do I need?

Flake coverage is set by the flake manufacturer or kit (pounds per square foot or per kit). Enter that rate from your data sheet or leave it blank. The calculator multiplies it by your floor area.

Is epoxy safe to use in a garage?

It can be, if you follow the product's label and SDS: ventilation, gloves and a respirator rated for the product, no ignition sources, and a plan for children, pets and fumes reaching a house through an attached garage. Read the full guide. Never use a fuel-burning heater to speed up a cure unless the label allows it.

Sources and further reading

  1. Rust-Oleum Technical Data ROC-109, Concrete & Garage 1-Part Epoxy Floor Paint + Primer (Rev. 030325): practical coverage 300-400 sq ft/gal smooth, 180-220 sq ft/gal porous, 15% material loss assumed (rustoleum.com) Opened 2026-11-17. Cited only as one example data sheet, not a recommendation.
  2. Armor Garage Heavy Tonnage Epoxy data sheet (HV100X, Rev 11/21): 125 sq ft per gallon at 30 mils, 100% solids (armorgarage.com) Opened 2026-11-17. Cited only to show the spread between product types.
  3. OSHA, Hazard Communication: manufacturers prepare labels and safety data sheets to convey hazard information (osha.gov) Opened 2026-11-17.
  4. CDC, About Carbon Monoxide Poisoning (fuel-burning appliances and garages) (cdc.gov) Opened 2026-11-17.

Related articles